My group and I had to open up two computer systems and build one to work with, so it could be set up to meet the needs of a specified user. I added a picture from when the system was taken apart to upgrade the components from a different computer system, then put them in to the completed system as shown below and then put the screws on the case to safely close it up. The components that were upgraded were the motherboard and the RAM( Random Access Memory). In addition, we added another hard drive to the system to provide it with more storage capacity.
After that, we connected all of the connections to and from the motherboard and re-cased the computer and put it in a safe place ready to be tested.
|
The computer system looked like this before completion. We dismantled both computers and gathered components that we wanted to use for our computer. We used a motherboard, RAM module(s), hard drive and processor from a newer computer to upgrade those components we took out from the older computer to boost the level of performance and stability. |
 |
| We were gathering our system components to use for our computer system. We needed the motherboard, case, processor, heat sink and the CD drive. We took out the motherboard by disconnecting the connections from the power supply and from the front panel of the case and installed it in the case shown below when the system was completed. |
|
We were in the final stages of gathering our components for our system. These components were used to set up and enable the system to operate in a safe and stable manner. The components we gathered were a new motherboard, RAM module(s), extra IDE hard drive and a more powerful processor. In addition, we had to disconnect the hard drive and the motherboard from the power supply to remove them. The processor and heat sink were left on the motherboard as they came with the motherboard and it was more powerful than the one we removed from the case shown below, when the system was completed and ready for testing and or troubleshooting. |
 |
At this point, the system was nearing completion. We were installing and connecting all of our components. The components we were connecting were the motherboard, CD drive and the floppy drive. In addition, we used a motherboard mannual to show us the correct way to connect the motherboard to the front panel of the case as well as any additional components. The motherboard went in the middle of the case so that the hard drive, CD drive, RAM and the floppy drive as well as cables and connections to make them more accessible. The IDE cables were used for the hard drive, CD drive and the floppy drive and the connections were towards the front of the case where the drives were installed. The RAM was installed in an allocated slot which is usually at the top of the motherboard. The processor was on a specially allocated socket on the motherboard (usually in the centre) and there are many types of sockets on the market on different motherboards( Intel 775 and 1156). The power supply was connected to the entire system to power it up and turn it on.
The connections we connected were for the power button, reset button, hard drive LED, power LED and the USB ports at the front of the case. |
 |
| Our computer was ready to be tested and troubleshooted as needed. We tested the system to see if it correctly identified the hardware on the system. In addition, we checked that it successfully booted up into the operating system. We did this by turning the system on and checking for any known issues with it as well as getting an idea on how to rectify them. |
 |
| I was locating the installation file from the download of Malwarebytes AntiMalware to install. The file was labeled as 'mbam-setup 1.51.2.1300'. The file was on my desktop and I double clicked on it to initiate the first step of the installation process which was to confirm that I was sure that I wanted to execute it. |
 |
| I received a warning before running the installation wizard. |
 |
| I chose the set up language to run installation and set up. |
 |
I followed the precautions before installing the software.
 |
| I read the terms and conditions of the software license for this program to see what I can and cannot do. |
|
 |
| I saw the bugs or issues fixed within the program. |
 |
| I had a choice of location for installation files for the software. |
 |
| I had the option to create start folders for the program. |
 |
| I now had the option for creating additional folders and icons. |
 |
| I confirmed the installation options for the software. |
 |
| I have finalised the installation of the program and waitied for the wizard to finish the installation. |
 |
| I could update and launch the program I have installed. |
 |
| I ran the update service to provide up to date virus definitions. |
 |
| This was a confirmation notice to tell me the update was successful. |
 |
| I launched the software after updating it and installing it to test for functionality. |
 |
| I tested the software in operation before and after the restart and it was successful. |
I have presented a screenshot on where I found the file for the installation.
 |
| I had to locate the Spybot Search and Destroy installer. |
 |
| I chose the setup language to run the set up of the software. |
 |
| This was the start of the installation which gave me some recommendations before continuing. |
 |
I read and agreed to the license terms and conditions to continue.
|
 |
| I specified a location for the installation files and then I continued with the process. |
 |
| I specified the type of installation and then I continued with the installation/ configuration process. |
 |
I named and created my start menu folders. This step could be avoided but for the purpose of my work, I performed this step.
 |
I specified which icons I wanted and how I wanted the software to run.
|
|
